Dingocroft (Penn Rental Service Ltd t/a) Series One Axles and Transmission Parts

Axle Breather Ref: 515845=
Application: Series 1, 2 & 3 and Range Rover Classic.
Description: Brass bodied axle breather with one way valve to stop ingress of water when wading.
Price: £2.20 (£2.59 Including VAT at 17.5%)

Seal Axle Tube. Ref: 217400
Application: Front axle of Series 1, 2 & 3.
Description: Oil seal in end of front axle tube. Angus/Gaco manufacture.
Approximate dimensions; overall diameter 63.5mm (2.5"), thickness 9mm (0.35")
Price: £2.10 (£2.47 Including VAT at 17.5%)

Gear Set - Differential Ref: RTC4489
Application: Series 1, 2 & 3 Rover type differentials.
Description: Matched set of gears and shims for differential.
Original part numbers; set includes 2 each of 06735 & 40760.
Price: £45.00 (£52.88 Including VAT at 17.5%)

Locker Differential Bolts Ref: 272922
Application: Series 1 & 2.
Description: Locker for crown wheel to differential housing bolts.

Price: £0.25 (£0.29 Including VAT at 17.5%)

Differential Casing Ref: 273441
Application: Series 1 & 2 Rover type differentials.
Description: Casing or housing for differential gears.
Price: £35.00 (£41.13 Including VAT at 17.5%)

Differential Housing Ref: 528257
Application: Series 1 and Series 2.
Description: Differential housing for both front and rear axles. Comes with caps and bolts for differential casing retention.
Original part number 219635
Price: £45.00 (£52.88 Including VAT at 17.5%)

Gasket for Differential to Axle Casing Ref: 7316
Application: Rover type differentials on Series 1, 2 & 3. Range Rover Classic, Defender and Discovery 1.
Description: replacement gasket for differential assembly to axle casing.
Approximate dimensions: overall diameter 24.4cm (9.6")
Price: £0.50 (£0.59 Including VAT at 17.5%)

Bearing, Differential Support Ref: 41045
Application: Series 1 and Series 2 differentials.
Description: Taper roller bearing used in pairs to support axle differential. Bearing is numbered 2729/2788.
Approximate dimensions: outside diameter 3" (76.4mm), inside diameter 1.5"(38mm).
Price: £15.00 (£17.63 Including VAT at 17.5%)

Cross-shaft for Differential Ref: 539703
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Cross-shaft for differential gears.
Approximate dimensions: overall length 123mm (4.85"), diameter 15.5mm (0.61").
Original part number 11378.
Price: £6.00 (£7.05 Including VAT at 17.5%)

Thrust Washer for Diff Wheels 0.040" Ref: 533786
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1mm (0.040")
Original part number 07902.
Price: £1.00 (£1.18 Including VAT at 17.5%)

Thrust Washer for Diff Wheels 0.045" Ref: 533787
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1.15mm (0.045")
Original part number 07904.
Price: £1.00 (£1.18 Including VAT at 17.5%)

Thrust Washer for Diff Wheels 0.050" Ref: 533788
Application: Series 1 differentials and Series2A Rover type differentials.
Description: Fibre thrust washer for differential wheels.
Approximate dimensions: outside diameter 69mm (2.72"), inside diameter 40mm (1.57"), thickness 1.3mm (0.050")
Original part number 50139.
Price: £1.00 (£1.18 Including VAT at 17.5%)

Shim for Inner bearing of Diff Pinion, 0.003" Ref: 230438
Application: Series 1 and Series 2 differentials.
Description: 0.003" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.41 Including VAT at 17.5%)

Shim for Inner Bearing of Diff Pinion, 0.005" Ref: 230439
Application: Series 1 and Series 2 differentials.
Description: 0.005" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.41 Including VAT at 17.5%)

Shim for Inner Bearing of Diff Pinion, 0.010" Ref: 230440
Application: Series 1 and Series 2 differentials.
Description: 0.010" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.41 Including VAT at 17.5%)

Shim for Inner Bearing of Diff Pinion, 0.020" Ref: 233677
Application: Series 1 and Series 2 differentials.
Description: 0.020" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 78.6mm (3.09"), inside diameter 67mm (2.64").
Price: £1.20 (£1.41 Including VAT at 17.5%)

Oil Seal Differential Pinion Ref: FRC4586
Application: Series 1, 2 & 3 Rover type differentials.
Description: Oil seal to nose of differential. Corteco/Gaco boxed.
Approximate dimensions: outside diameter 70mm (2.76"), thickness 12.5mm (0.5").
Original part number: 217507.
Price: £2.96 (£3.48 Including VAT at 17.5%)

Brass Gasket Differential Nose Ref: 553412=
Application: Series 1 and Series 2 differentials.
Description: Brass gasket/shim for nose peice of differentials. 0.2mm (0.008") thick
Original part number 233473.
Price: £1.00 (£1.18 Including VAT at 17.5%)

Shim for Outer Bearing of Diff Pinion, 0.010" Ref: 219549
Application: Series 1 and Series 2 differentials.
Description: 0.010" shim for setting position of differntial pinion and bearing pre-load.
Approximate dimensions: outside diameter 41mm (1.6"), inside diameter 32.5mm (1.28").
Price: £0.75 (£0.88 Including VAT at 17.5%)

Nut and Bolt Kit for Propshafts Ref: PROPFIX01
Application: Series 1, Series 2, Series 2A, Series 3 Land Rovers. All Defenders, Classic Range Rover, Range Rover 2 (38A), Discovery 1 and Discovery 2.
Description: Set of four 3/8UNF x 1.125" long bolts plus four short nyloc nuts.
Price: £1.27 (£1.49 Including VAT at 17.5%)

Replacement Universal Joint Kit Ref: RTC3291=
Application: Series 1 and Series 2/2A to approximately 1964.
Description: Universal joint repair kit including 4 circlips and a grease nipple.
Approximate Dimensions: Distance across faces of joint 75mm (2.95"), cap diameter 27mm (1.06"), cap length including seal 17mm ( 0.67").
Original part number 43023.
Price: £7.00 (£8.23 Including VAT at 17.5%)

Related products:

1. Nut and Bolt Kit for Propshafts (Ref: PROPFIX01)

2. Spanner for propshaft nuts and bolts (Ref: ZZBRIRJ562A)

Yoke for Propellor Shaft Ref: 262468
Application: Series 1 & 2.
Description: Yoke for propellor shaft. Only suitable for original prop shafts with the smaller universal joints - RTC3291.
Price: £15.00 (£17.63 Including VAT at 17.5%)

Genuine Propshaft Gaiter Ref: 276484
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.
Description: Genuine gaiter and 2 clips for sliding joint on front and rear propellor shafts.
Price: £8.58 (£10.08 Including VAT at 17.5%)

Replacement Propshaft Gaiter Kit Ref: 276484D
Application: Series 1, Series 2/2A, Series 3, early 90/110, Classic Range Rover.
Description: Replacement gaiter and 2 clips for sliding joint on front and rear propellor shafts.
Price: £3.00 (£3.53 Including VAT at 17.5%)

Drain Plug - Axle Casing Ref: 235592
Application: Series 1 & 2.
Description: Solid brass drain plug.
Approximate dimensions: outside diameter 34.8mm (1.37"), hight 17.7mm (0.7").
Price: £6.95 (£8.17 Including VAT at 17.5%)

Related products:

1. Washer for Drain Plug (Ref: 515599)

Washer for Drain Plug Ref: 515599
Application: Series 1 & 2.
Description: Copper crush washer for axle drain plug.
Approximate dimensions: outside diameter 35mm (1.4").
Origilal part number 230509.

Price: £0.36 (£0.42 Including VAT at 17.5%)

Hub Bearing Rear Ref: 270604
Application: Series 1 with the semi-floating rear axle , that is most of them.
Description: Replacement rear hub bearing. This is the one that is a swine to change. Bearing number 88128R, with shields on both sides.
Approximate dimensions: outside diameter 80mm (3.15"), inside diameter 39mm (1.54"), thickness of outer race 21mm (0.83"), thickness of inner race 27.4mm (1.08").

Price: £50.02 (£58.77 Including VAT at 17.5%)

Rear Hub Oil Seal Ref: 236923
Application: Series 1 with semi-floating rear axle.
Description: Replacement rear hub oil seal.
Approximate dimensions: outside diameter 70mm (2.76"), thickness 12mm (0.47").
Price: £3.25 (£3.82 Including VAT at 17.5%)

Series 2 and Series 3 Hub Bearing Kit Ref: WHEELBRGKIT01
Application: Series 1 front axle only, Series 2, Series 2A and Series 3 to 1980. Where inner bearing is larger than outer bearing. Covers both long and short wheel base vehicles, suitable for either front or rear wheel.
Description: Kit of parts to service one wheel hub. Kit comprises inner and outer Timken wheel bearings, Gaco inner seal, flange gasket, hub nut locker, felt outer seal, 'o' ring outer seal and split pin.
Price: £35.77 (£42.03 Including VAT at 17.5%)

Stud for wheel Nut Ref: 561590D
Application: Series 1 and Series 2 wheel hubs.
Description: Threaded stud 9/16" BSF x overall length of 43mm (1.6").
Original part number 217360.
Price: £0.76 (£0.89 Including VAT at 17.5%)

Retaining Collar Half-Shaft Bearing Ref: 90217398D
Application: Series 1, 2 & 3 front axle.
Description: Replacement retaining collar for inner race of bearing for front half shafts'
Approximate dimensions: outside diameter 44.4mm(1.75"), inside diameter 34.8mm (1.25"), length 25mm (1.0")
Original part number: 217398
Price: £7.20 (£8.46 Including VAT at 17.5%)

Bearing for Front Half-Shaft Ref: 244150=
Application: Series 1, 2 & 3 front axles.
Description: Branded single row roller bearing for supporting front half shaft in end of axle tube.
Approximate dimensions: outside diameter 76.4mm (3"), inside diameter 35mm (1.375"), length 18.5mm (0.73").
Price: £13.10 (£15.39 Including VAT at 17.5%)

Universal Joint for Front Half-Shafts Ref: RTC3690
Application: Series 1 1952 onwards, Series 2 & 3 front axles.
Description: GKN boxed universal joint for front half-shafts.
Approximate dimensions: 75.5mm (3") across caps, 27mm (1.06") diameter caps.
Original part number: 242521
Price: £12.00 (£14.10 Including VAT at 17.5%)

Locker Swivel Pin Bolts 3/8" diameter Ref: 270287
Application: Series 1 swivel pin housings and early Series 2 ones.
Description: Locker for 3/8" diameter swivel pin bolts.
Price: £0.40 (£0.47 Including VAT at 17.5%)

Replacement Swivel Housing S1, S2a & S3 Ref: 539741D
Application: Series 1, Series 2 & 2A, Series 3 (except 109 V8).
Description: Replacement swivel housing for front axle.
Original part number: 234789.
Price: £69.90 (£82.13 Including VAT at 17.5%)

Swivel Pin Bearing Ref: 217268+
Application: Series 1, 2 & 3.
Description: Timken 21075 taper roller bearing. Fitted to lower swivel pin on front axle.
Approximate dimensions: outside diameter 54mm (2.13"), inside diameter 19mm (0.75")
Price: £9.99 (£11.74 Including VAT at 17.5%)

Gasket Swivel Housing to Axle Tube Ref: 232413
Application: Series 1, 2 & 3 front axles.
Description: Replacement paper gasket for swivel housing to front axle tube.
Approximate dimensions: overall diameter 12.8cm (5")
Price: £0.15 (£0.18 Including VAT at 17.5%)

Swivel Housing Outer Seal Ref: RTC3528
Application: Series 1, 2 & 3 front axles.
Description: UK made oil seal for swivel housings.
Approximate dimensions: \outside diameter 16.8cm (6.6"), thickness 14.7mm (0.58")
Original part number: 502406.
Price: £4.18 (£4.91 Including VAT at 17.5%)

Retainer Swivel Housing Oil Seal Ref: 235968D
Application: Series 1, 2 & 3.
Description: Reproduction pressed steel retainer for oil seal to swivel housing.
Approximate dimensions: outside diameter 203mm (8"), inside diameter 157mm (6.18").
Price: £1.10 (£1.29 Including VAT at 17.5%)

Locker for Stub Axle Ref: 277311D
Application: Series 1, 2 & 3.
Description: Replacement locker for stub axle and brake back plate to swivel housing and/or to rear axle tube.
Approximate dimensions: Hole centres 58mm (2.3"), hole diameter 10mm (3/8")
Price: £0.25 (£0.29 Including VAT at 17.5%)

Felt Seal Stub Shaft to Drive Flange Ref: RTC3515
Application: Series 1 front axles, Series 2 front and rear axles, Series 3 SWB front and rear axles.
Description: Felt seal for 10 spline axle shafts to outer drive flanges.
Original part number 272086
Price: £0.40 (£0.47 Including VAT at 17.5%)

Inner Wheel Hub Seal Ref: RTC3510
Application: Series 1 front axles, Series 2 & Series 3 to 1980.
Description: Inner hub oil seal made by Corteco/Gaco.
Approximate dimensions: outside diameter 85mm (3.35"), thickness 7.8mm (0.3").
Original part number 239422.

Price: £3.50 (£4.11 Including VAT at 17.5%)

Inner Hub Bearing Ref: RTC3416
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Inner wheel hub bearing. Timken taper roller bearing 359S/354X.
Approximate dimensions: outside diameter 85mm (3.35"), inside diameter 46mm (1.8").
Original part number 217269
Price: £18.50 (£21.74 Including VAT at 17.5%)

Outer Hub Bearing Ref: RTC3426
Application: Series 1 front hubs, Series 2 & 2A front and rear hubs, Series 3 front and rear hubs to 1980.
Description: Outer wheel hub bearing. Timken taper roller bearing 11162/11300.
Approximate dimensions: outside diameter 76.5mm (3.0"), inside diameter 41.2mm (1.62").
Original part number 217270
Price: £14.97 (£17.59 Including VAT at 17.5%)

Locker for Hub Nuts Ref: 217353=
Application: Series 1, 2 & 3. Range Rover Classic and early Defender.
Description: Locker for wheel hub nuts.
Approximate dimensions: outside diameter 64.5mm (2.54"), inside diameter 41.6mm (1.64"), thickness 1.0mm *(0.040")
Price: £0.45 (£0.53 Including VAT at 17.5%)

Flange Gasket Ref: 231505=
Application: Series 1, 2 & £.
Description: Paper gasket for drive flange to wheel hub.
Approximate dimensions: outside diameter 112mm (4.4"), inside diameter 77mm (3")
Price: £0.20 (£0.24 Including VAT at 17.5%)