Dingocroft (Penn Rental Service Ltd t/a) Other tools

Remover Fuel Pump and Sender Units Ref: LRT-19-001
Application: Plastic fuel tanks on Range Rover Classic, Range Rover 2, Discovery 1, Discovery2 and Defender.
Description: Wrench for removing plastic retaining ring on plastic fuel tanks.
Old tool number: LST.131
New tool number: 310-112
Approximate dimensions: overall diameter 16cm (6.3"), height 13cm (5.1")
Price: £59.25 (£68.14 Including VAT at 15%)

Fuel Pressure Guage Ref: LRT-19-004A
Application: Pretty much universal.
Description: Fuel pressure guage reading to 4 bar (60psi). Supplied with hoses and 'T' piece to allow connection to fuel line.
Price: £75.85 (£87.23 Including VAT at 15%)

Wrench, Fuel Tank Sender/Pump Unit Ref: LRT-19-009
Application: Defender TD5, Discovery 2, Freelander 1 and Range Rover 38A
Description: Wrench for removing the fuel tank sender/pump unit. On these models the sender unit (which incorporates fuel pump in most cases) is retained by a large plastic threaded ring. This is difficult to remove without damage unless this tool is used.
Price: £80.16 (£92.18 Including VAT at 15%)

Replacer Pinion Oil Seal on Rover Type Diffs Ref: LRT-51-001
Application: Ser2A, Ser3, Range Rover Classic, Defender and Discovery.
Description: Pinion oilseal installer for use on Rover type differentials. Allows seals to be fitted square and to the correct depth.
Old part number: LST.106
Price: £39.34 (£45.24 Including VAT at 15%)

Replacer Pinion Oil Seal - Salisbury Axles Ref: LRT-51-002
Application: Salisbury axles on Series 3 and Defender.
Description: Pinion oilseal installer for use on Salisbury type differentials. Allows seals to be fitted square and to the correct depth.
Approximate dimensions: length 86mm (3.4"), overall diameter 78mm (3.1").
Old part number: RO1008A
Price: £55.54 (£63.87 Including VAT at 15%)

Adjustable Flange Holding Tool Ref: LRT-51-003
Description: Tool for holding the input flange of differentials. This facilitates the removal of the flange retaining nut or bolt.
Application: All models.
Old tool part number: 18G.1205.
Approximate dimensions: overall length 55.5cm.
Price: £96.15 (£110.57 Including VAT at 15%)

Remover for the Differential Flange Centraliser Ref: LRT-51-008
Description: The tool to remove the centraliser in the rear differential propshaft drive flange. Those fitted with the rubber doughnut joint.
Application: Discovery I from approx 1994 to 1999.
Price: £92.81 (£106.73 Including VAT at 15%)

Replacer Pinion Oil Seal Ref: LRT-51-009
Application: Defender 90 rear axle with 4 pin diff carrier, Range Rover 38A 1995 to 2002 both diffs.
Description: Tool for replacing the pinion oil seal on differentials. The tool fits the seal square and to the correct depth.
Approximate dimensions: length 106mm (4.2"), overall diameter 90mm (3.54").
Price: £39.06 (£44.92 Including VAT at 15%)

Height Guage Rear Differential Ref: LRT-51-018/1
Application: Defender Rear Differential approx 2003 onwards.
Description: Pinion bearing height setting tool. Use with LRT-51-018/7.
New tool number: 205-696

Price: £166.24 (£191.18 Including VAT at 15%)

Mounting Bridge Ref: LRT-51-018/7
Application: Defender rear axle from 2002 onwards.
Description: Mounting bridge for pinion height guage. Use with LRT-51-018/1.
New tool number: 205-702
Price: £195.55 (£224.88 Including VAT at 15%)

Related products:

1. Height Guage Rear Differential (Ref: LRT-51-018/1)

Adaptor for the Removal of Pinion Bearing Cone Ref: LRT-51-500
Application: Salisbury axles as fitted to Series 2A, Series 3 and Defender models.
Description: Adaptor for the removal of the pinion bearing cone on Salisbury axles. Used in conjunction with Special Tool LRT-99-002.
Old part number: 18G.47BK
Price: £73.40 (£84.41 Including VAT at 15%)

Related products:

1. Hand Press (Ref: LRT-99-002)

Differential Case Compressor Ref: LRT-51-503
Application: Salisbury axles on Series 3 and Defender. (Also aplicable to some Jaguar models!!)
Description: Tool for compressing the Salisbury axle casing in the vertical plane. This allows the differential to be removed.
This tool does the same job as the earlier spreader and pins referred to in some workshop manuals.
Old parrt numbers: 18G131c, 18G131F & GKN131
Price: £250.66 (£288.26 Including VAT at 15%)

Adaptor for Replacement of Hub Oil Seals Ref: LRT-54-001
Application: Range Rover Classic, Defender and Discovery 1.
Description: Adaptor for use with LRT-99-003, to set hub oil seals squarely to the correct depth.
Old tool number: LST550-5
Price: £31.61 (£36.35 Including VAT at 15%)

Related products:

1. Replacer Bearings and Oilseals - Main Tool (Ref: LRT-99-003)

Hub nut box spanner (not Churchill's) Ref: LRT-54-002
Application: Series I-III, Defender, Discovery I and Range Rover Classic.
Description: Hub adjustment wrench. NB this is not a Churchill tool
Old part number: RO.606435A

Price: £10.17 (£11.70 Including VAT at 15%)

Installer Hub Oil Seal Ref: LRT-54-003
Application: Range Rover Classic 1986 on including early models with ABS.
Description: Hub oilseal installer. Allows seals to be fitted square and to the correct depth.
Weight: 0.858kg

Price: £37.45 (£43.07 Including VAT at 15%)

Replacer Upper Ball Joint Ref: LRT-54-021
Application: Discovery 2.
Description: Tool for replacing upper swivel ball joint on front axle. Use in conjunction with LRT-54-008-M/
New tool number: 205-732
Price: £81.39 (£93.60 Including VAT at 15%)

Ball Joint bSplitter Ref: LRT-54-027
Application: Discovery 2, Discovery 3, Range Rover 3, Range Rover Sport and vFreelander 2.
Description: Large Capacity ball joint splitter for suspension and steering ball joints.
New part number: 205-754A
Price: £206.26 (£237.20 Including VAT at 15%)

Hub oil seal Replacer Ref: LRT-54-501
Application: Ser2A, Ser3, Range Rover Classic, Defender.
Description: Hub oilseal replacer for vehicles up to 1985. Allows seals to be fitted square and to the correct depth.
Weight: 0.80kg
Old part number: 18G1349

Price: £34.97 (£40.22 Including VAT at 15%)

Pinion Head Bearing Remover/Replacer Ref: LRT-54-502
Application: Rover type differentials on Series vehicles, Classic Range Rover, Discovery 1 and Defender.
Description: Used with hand press ZZLRT-99-002 to remove and replace the pinion head bearing.
Old tool number: 18G47-6
Price: £92.42 (£106.28 Including VAT at 15%)

Related products:

1. Hand Press (Ref: LRT-99-002)

Pinion Height Gauge Ref: LRT-54-503
Application: Rover and Salisbury type differentials. So most models except very latest and Freelander 1.
Description: Pinion height setting tool with steps of 30.93mm, 38.10mm and 39.50mm. Used in conjunction with dial gauge.
Old tool number: 18G191-4
New tool number: 205-743
Price: £61.81 (£71.08 Including VAT at 15%)

Related products:

1. Metric dial gauge. (Ref: ZZFRATA453)

Extractor Pinion Bearing Cup Ref: LRT-54-505
Application: All models using Rover type differentials, ie Series 1, 2, 2A, 3, Classic Range Rover, Defender and Discovery 1.
Description: Main tool for extracting pinion bearing cups from differential housings. Used in conjunction with LRT-54-506 and LRT-54-507.
Old part number: RO.262757A
Price: £88.06 (£101.27 Including VAT at 15%)

Related products:

1. Adaptor for Pinion Head Bearing Cup (Ref: LRT-54-506)

2. Adaptor for Pinion Tail Bearing Cup (Ref: LRT-54-507)

Adaptor for Pinion Head Bearing Cup Ref: LRT-54-506
Application: All models using Rover type differentials, ie Series 1, 2, 2A, 3, Classic Range Rover, Defender and Discovery 1.
Description: Adaptor for extracting pinion head bearing cup from differential housings. Used in conjunction with LRT-54-505.
Old part number: RO.262757-1.
Approximate dimensions: Overall diameter 81mm (3.19"), thickness 20mm (0.79").
Price: £32.45 (£37.32 Including VAT at 15%)

Related products:

1. Extractor Pinion Bearing Cup (Ref: LRT-54-505)

Adaptor for Pinion Tail Bearing Cup Ref: LRT-54-507
Application: All models using Rover type differentials, ie Series 1, 2, 2A, 3, Classic Range Rover, Defender and Discovery 1.
Description: Adaptor for extracting pinion tail bearing cup from differential housings. Used in conjunction with LRT-54-505.
Old part number: RO.262757-2.
Approximate dimensions: Overall diameter 66mm (2.6"), thickness 10mm (0.375").
Price: £33.19 (£38.17 Including VAT at 15%)

Related products:

1. Extractor Pinion Bearing Cup (Ref: LRT-54-505)

Adjusting Screw Tool for Steering Box Ref: LRT-57-006
Application: Adwest and Gemmer power steering boxes as fitted to Defender, Range Rover Classic and Discovery 1.
Description: Adaptor to allow easy adjustment on these steering boxes. Takes 1/2" drive socketry.
Approximate dimensions: 41mm (1.61") hexagon across flats, 30mm (1.18") high.
Old part number: LST119A
Price: £80.77 (£92.89 Including VAT at 15%)

'C' Spanner for Steering Box Ref: LRT-57-007
Application: Defender, Range Rover Classic and Discovery 1 when fitted with Adwest power steering box.
Description: 'C' wrench (or spanner) for adjusting the lock nut on these sterring boxes.
Old part number: LST120
Approximate dimensions: overall length 233mm (9.2"), pin centres 75mm (2.95").
Price: £38.85 (£44.68 Including VAT at 15%)

Torque Setting Tool for Steering Box Ref: LRT-57-017
Application: Adwest and Gemmer power and manual steering boxes as fitted to Defender, Range Rover Classic and Discovery 1.
Description: Tool to allow correct torque setting of the above steering boxes.
Old Part number: RO1016
Approximate dimensions: overall diameter 63.5mm (2.5"), internal diameter 19mm (0.75"), height 25mm (1.0")
Price: £19.95 (£22.94 Including VAT at 15%)

Ring Expander for Seals Ref: LRT-57-019
Application: Adwest and Gemmer power steering boxes as fitted to Range Rover Classic, Discovery 1 and Defender.
Description: Ring expander for steering box valve and worm seals.
Approximate dimensions: Length 104mm (4.1"), diameter 37.8mm (1.49")
Old part number: RO.606602
Price: £29.41 (£33.82 Including VAT at 15%)

Puller for Steering Drop Arm Ref: LRT-57-500
Application: Series 2, 2A and 3.
Description: Puller for the removal of the drop arm from the main steering box.
Old part number: RO.600000.
Approximate dimensions: Jaw width 60mm (2.36"), overall width 91mm (3.6"), height excluding bolt 70mm (2.76"),
thickness 24mm (0.95").
Price: £94.33 (£108.48 Including VAT at 15%)

Height Guage Set Range Rover Ref: LRT-60-003
Application: Range Rover 38A (2nd Generation) 1995 to 2000)
Description: Suspension height guage set, comprising 4 short blocks and 4 tall blocks in black plastic carry case.
Approximate dimensions: Overall diameterof each guage 50mm (2"), short block height 70mm (2.76"), tall block height 136mm (5.35")
Price: £166.43 (£191.39 Including VAT at 15%)

Remover/Replacer Radius Arm Bush Ref: LRT-60-004
Description: Tool for the removal and replacement of radius arm bushes. Probably for use with a hydraulic press.
Application: Range Rover 2nd Generation (38A) 1995 to 2002.
Price: £97.47 (£112.09 Including VAT at 15%)

Replacer/Remover Upper Arm Bushes Ref: LRT-64-024
Application: Range Rover Generation 3, 2002 onwards.
Description: Tools for removing and replacing the upper arm bushes on the rear suspension.
Price: £101.75 (£117.01 Including VAT at 15%)

Remover/Replacer Hub Bush Upper Ref: LRT-64-025
Application: Range Rover Generation 3, 2002 onwards.
Description: Tools for removing and replacing the upper hub bush on the rear suspension.
Price: £89.17 (£102.55 Including VAT at 15%)

Compressor for Caliper Pistons Ref: LRT-70-500
Application: Range Rover Classic, Defender and Discovery 1.
Description: Tool for pushing pistons back into brake caliper and also for fitting piston seals and retainers.
Old part number: 18G.672
Price: £106.05 (£121.96 Including VAT at 15%)

Key for Alpine Radio Removal Ref: LRT-86-006
Application: Range Rover 38A (2nd generation) and other models where 'Alpine' brand radios are fitted.
Description: Single key for radio removal, but TWO keys are needed to remove radio.
Approximate dimensions: overall length 98mm.
Price: £12.33 (£14.18 Including VAT at 15%)

Hand Press Ref: LRT-99-002
Application: Universal tool, used in conjunction with many tools in all areas of the vehicles.
Description: Hand press.
Approximate dimensions: Overall height 54cm (21.3"), maximum opening 15cm (5.9"), between pillars 14.5cm (5.7")
Price: £394.45 (£453.62 Including VAT at 15%)

Replacer Bearings and Oilseals - Main Tool Ref: LRT-99-003
Application: Universal.
Description: Main tool for replacing bearings and oil seals, used with various adaptors for specific tasks.
Old tool number: 18G134
Price: £36.16 (£41.58 Including VAT at 15%)

Impuse Extractor (Slide Hammer) - Main Tool Ref: LRT-99-004
Application: General purpose tool, used in conjunction with various other tools where impulse extraction is needed.
Description: Hefty slide hammer weighing 3.5kg. End collars threaded 5/8"UNF and 7/8"UNF. Overall length 40cm (15.75").
Price: £77.42 (£89.03 Including VAT at 15%)